About Microsoft PL-200 Exam Test Dumps

Third, we offer 24/7 customer assisting to support if you have any problems about the downloading or purchasing the PL-200 vce dumps, Our PL-200 Study Guide - Microsoft Power Platform Functional Consultant exam dumps are the latest by updating constantly and frequently, Now, in order to make you feel relieved, we promise you that you can get full refund if you failed in the IT exam even with the help of our PL-200 online exam practice, Microsoft PL-200 Frequent Updates PDF version: Easy to read and print.

The improvements are currently being rolled out and give developers new https://examtorrent.actualcollection.com/PL-200-exam-questions.html and enhanced features to assist in marketing their apps, assembly=System.Windows.Interactivity >

See the explanation below:
Answer:
Explanation:
Explanation
Switch 1 port E0/1 WAS CONNECTED TO A COMPUTER WITH A STRAIGHT THROUGH CABLE AND AS WELL AS ROLLOVER CABLE (FOR CONFIGURATION OF SWITCH PORTS ON THIS SWITCH) WHICH WAS SHOWN IN VLAN 600 IN THE DIAGRAM BUT ACTUALLY THAT PC WAS NOT IN VLAN 600 AFTER CHECKING THE VLAN CONFIGURATION USING SHOW VLAN COMMAND. INSTEAD THIS PORT WAS CONFIGURED IN VLAN 1. SO WE NEEDED TO PUT THAT PC IN VAN 600 USING FOLLOWING COMMANDS-SW1(CONFIG)# INTERFACE E0/0SW1(CONFIG-IF)#SWITCHPORT MODE ACCESSSW1(CONFIG-IF)#SWITCHPORT ACCESS VLAN 600 NOW THE E0/0-PORT OF THIS SWITCH-SW1 WAS RECEIVING NATIVE VLAN MISMATCH FROM SW3 SWITCH-PORT E0/1. ALSO E0/0 OF SW1 AND E0/1 OF SW3 WERE NOT IN TRUNKING MODE.
AND THE QUESTION WAS ASKED TO MAKE SURE THAT CONNECTION BETWEEN BOTH
SWITCHES SHOULD BE IN TRUNKING MODE WITH 802.1Q ENCAPSULATION ENABLEDSO USED THE BELOW COMMANDS-SW1(CONFIG)#INT E0/0SW1(CONFIG-IF)#SWITCHPORT TRUNK ENCAPSULATION DOT1QSW1(CONFIG-IF)# SWITCHPORT MODE TRUNK.
ON OTHER SWITCH WHICH IS SWITCH3
SW3(CONFIG)#INT E0/0SW3(CONFIG-IF)#SWITCHPORT TRUNK ENCAPSULATION
DOT1QSW3(CONFIG-IF)# SWITCHPORT MODE TRUNK.SW3(CONFIG-IF)# SWITCHPORT TRUNK NATIVE VLAN 1 ALSO PORT E0/2 OF SW3 WAS CONNECTED TO SERVER AND IN VLAN 600 AND PORT E0/3 WAS ASSIGNED TO VLAN 500 AND TO A COMPUTER AGAIN IN VLAN 500 ITSELF. SO THAT COMPUTER HAD A CONSOLE CABLE CONNECTED TO SW3 AS WELL IN ORDER TO CONFIGURE SW3 PORTS AS TRUNK PORTS AND SWITCHPORTS USING THE ABOVE STEPS FOR SW1 WHICH WAS MENTIONED ABOVE.
SIMILARLY SW2 PORT E0/1 PORT WAS CONNECTED TO E0/4 PORT OF SW3 SO AGAIN TRUNK LINK CONFIGURATIONS BETWEEN E0/1 AND E0/4 PORTS BETWEEN TWO SWITCHES NEED TO EB DONE HERE. BUT YOU NEDD NOT TO AGAIN RUN THAT NATIVE VLAN COMMAND CHANGE ON SW3 OR SW2 SINCE ON SW3 WE AKREADY CHANGED IN ABOVE STEP AND IN SW2 ITS FINE IN VLAN 1 ONLY.
A COMPUTER WAS CONNECTED TO PORT E0/2 OF SW2 AND WAS IN VLAN 600 AND E0/3 WAS CONNECTED TIO SERVER WHCH WAS IN VLAN 600 AGAIN. ALSO AGAIN THIS TIME THE COMPUTER WAS CONNECTED TO THE SWITCH USING A CONSOLE CABLE ASWELL TO GIVE YOU CONSOLE ACCESS TO CONFIGURE AND VERIFY THE CONFIGURATIONS ON SW2. SO JUST VERIFY THE ACCESS PORTS ARE CORRECTLY ASSIGNED AND TRUNK PORTS AS WELL USING BELOW COMMANDS.